SANIVITE Automatic Sump Pump, 4/10 hp, 120 VAC, 1 ph
PartSAF008
MFG008
Description
Saniflo® Drain Pump, 18 gpm Flow Rate, 2 in Side, 1-1/2 in Top Inlet, 1 to 1-1/2 in Outlet, 120 VAC, 4.5 A, 1 ph, 16 ft Maximum Head, 140 deg F, 3600 rpm Motor
Price/Availability Accessible On Login
- Drain pump for kitchen installation or for any gray water application
- 16 ft vertical and/or 150 ft horizontal discharge
- The perfect quiet solution to install a kitchen or sink anywhere you never thought possible
- Capability to handle hot water and grease buildup
- Pre-assembled system with low inlets and built-in check valves
- Perfect for retrofit applications as unit can be adapted to discharge through a larger diameter line
The SANIVITE® is a drain pump that is ideally suitable for use in a basement apartment or anywhere in the house where additional fixtures are most wanted. It will pump waste water away from a variety of sources such as - a kitchen sink, laundry sink, washing machine (indirect connection), dishwasher, bar sink and more. The SANIVITE® model was designed to sustain the toughest applications meant for gray water pumps. Its pumping capabilities and unique design are the reason why these range of pumps are preferred for heavy duty applications. The inside of the SANIVITE® is comprised of a pressure chamber, which starts and stops the unit and the motor, which drives the pump. When the water enters the SANIVITE®, it activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A spindle/shaft drives the impeller and therefore the moving parts are kept to an absolute minimum. Water enters the chamber and is pumped away into the sanitary sewer. The unit pumps the effluent upward to 16 ft and/or 150 ft horizontally (with gravity fall). Once the water is discharged and the water level in the container goes down, the micro switch deactivates the unit until water enters the unit again. A normal operating cycle for the SANIVITE® can be as short as 2 to 10 s depending upon the discharge pipe run configuration, power consumption is therefore minimal. In addition to a sink, the SANIVITE® will also accept and discharge the waste water from a variety of other sanitary fixtures such as - a shower, a bathtub, a urinal and a whirlpool. When adding a bathtub or shower, a base will have to be constructed. This base should be made out of a 2 x 6 in (minimum) or 2 x 8 in (recommended) on edge, to allow for the installation of a P-trap and the required 1/4 in per ft gravity flow towards the pump unit. The waste water from other sanitary fixtures is discharged into the SANIVITE® via two 1-1/2 in inlets, on either side of the housing and an additional inlet on the t
Type | Automatic |
Series | SANIVITE |
Power Rating | 4/10 hp |
Voltage Rating | 120 VAC |
Phase | 1 ph |
Amperage Rating | 4.5 A |
Flow Rate | 18 gpm |
Horsepower | 4/10 hp |
Inlet Size | 2 x 1-1/2 in |
Maximum Head | 16 ft |
Motor Speed | 3600 rpm |
Outlet Size | 1 to 1-1/2 in |
Temperature Rating | 140 deg F |
Brand | Saniflo® |
Package Width | 16.25 in |
Package Height | 13 in |
UNSPSC | 40151500 |
Package Length | 9.5 in |
Country of Origin | FR |
Manufacturer | Saniflo |
UPC | 859925002084 |
Manufacturer Part Number | 008 |
3 Years Limited
cCSAus Certified|CSA C22.2|UL 788 Listed
Commercial/Residential Applications
Price/Availability Accessible On Login
- Recommended Accessories
- Competitive Brands
- Recently Viewed
No applicable products
No applicable products
No applicable products

Saniflo®SANIVITE Automatic Sump Pump, 4/10 hp, 120 VAC, 1 ph
- Customers Also Purchased
No applicable products