SANISHOWER Automatic Sump Pump, 2/10 hp, 120 VAC, 1 ph
PartSAF010
MFG010
Description
Saniflo® Drain Pump, 14 gpm Flow Rate, 2 in Side, 1-1/2 in Top Inlet, 3/4 in Outlet, 120 VAC, 5.5 A, 1 ph, 12 ft Maximum Head, 104 deg F, 3600 rpm Motor
Price/Availability Accessible On Login
- Residential drain pump for gray water applications
- 12 ft vertical and/or 100 ft horizontal discharge
- Easy to install and small enough to fit underneath a shower base
- Pre-assembled system with low inlets and built-in check valves
- It gives you a fast and easy way to add an additional sink and or shower to your home
The SANISHOWER® is a small drain pump that may be used to pump waste water away from a shower, sink, bar sink or other fixture. The SANISHOWER® is small enough to fit underneath a raised shower base. Alternatively, it can be placed behind a wall or beside a shower. The SANISHOWER® will pump wastewater up to 12 ft in height and/or 100 ft away from a soil stack. As a point of interest, quite a few pedicure manufacturers are putting the SANISHOWER® inside pedicure chairs. Due to its quiet operation and ease of installation, they have become the choice of OEM's. The inside of the SANISHOWER® is comprised of a pressure chamber, which starts and stops the unit and the motor, which drives the pump. When the water enters the SANISHOWER®, it activates a micro switch in the pressure chamber, which in turn starts the motor. The motor is sealed for life in an oil filled enclosure. A spindle/shaft drives the impeller and therefore the moving parts are kept to an absolute minimum. Water enters the chamber and is pumped away into the sanitary sewer. The unit pumps the effluent upward to 12 ft and/or 100 ft horizontally (with gravity fall). Once the water is discharged and the water level in the container goes down, the micro switch deactivates the unit until water enters the unit again. A normal operating cycle for the SANISHOWER® can be as short as 2 to 10 s depending upon the discharge pipe run configuration, power consumption is therefore minimal. In addition to sinks, the SANISHOWER® will also accept and discharge the waste water from a variety of other sanitary fixtures such as - a shower, a urinal and more. When adding a shower, a base will have to be constructed. This base should be made out of a 2 x 6 in (minimum) or 2 x 8 in (recommended) on edge, to allow for the installation of a P-trap and the required 1/4 in/ft gravity flow towards the pump unit. The discharge elbow on the side of the SANISHOWER® can be rotated 360 degrees to fit any type of installation required. A non-return valve, which comes already assembled o
Type | Automatic |
Series | SANISHOWER |
Power Rating | 2/10 hp |
Voltage Rating | 120 VAC |
Phase | 1 ph |
Amperage Rating | 5.5 A |
Flow Rate | 14 gpm |
Horsepower | 2/10 hp |
Inlet Size | 2 x 1-1/2 in |
Maximum Head | 12 ft |
Motor Speed | 3600 rpm |
Outlet Size | 3/4 in |
Temperature Rating | 104 deg F |
Brand | Saniflo® |
Package Width | 13.5 in |
Package Height | 9 in |
UNSPSC | 40151500 |
Package Length | 8 in |
Country of Origin | FR |
Manufacturer | Saniflo |
UPC | 859925002107 |
Manufacturer Part Number | 010 |
3 Years Limited
cCSAus Certified|CSA C22.2|UL 788 Listed
Medium Duty Applications
Price/Availability Accessible On Login
- Recommended Accessories
- Competitive Brands
- Recently Viewed
No applicable products
No applicable products
No applicable products

Saniflo®SANISHOWER Automatic Sump Pump, 2/10 hp, 120 VAC, 1 ph
- Customers Also Purchased
No applicable products