Commercial Heat Pump Air Handler, 7.5 ton, 2-Stage, R410A, 208-240/3, Standard, Belt VFD Low Static
PartRUURHCLP2090CAR
MFGRHCLP2090CAR
Description
RUUD® RHCLP2090CAR Commercial Heat Pump Air Handler, 7.5 ton, 2-Stage, R410A, 208-240/3, Standard, Belt VFD Low Static
Notice
Price/Availability Accessible On Login- C-20 LICENSE & EPA CERTIFICATE REQUIRED FOR PURCHASE OF THIS PRODUCT
- DISCONTINUED ITEM *ALL SALES FINAL* NO RETURNS
- CABINET - Powder coat painted. Matching discharge plenums and decorative supply and return air grilles are available for use when units are to be installed within conditioned space.
- MOTOR - Inherently protected motors are mounted inside of insulated cabinet to reduce motor noise. A choice of motor horsepowers and drive combinations are available to allow you to meet specified CFM at various static pressures up to 2" [.498 kPa] external static pressure.
- LOW PROFILE - Allows for horizontal installation in most stan-dard drop ceiling applications, and the movement of units through most standard doorways for addition or replacement work.
- THERMAL EXPANSION VALVES - Standard all models.
- FILTERS - One inch [25 mm] throwaway filters are standard, but filter racks are designed to accept either one inch [25 mm] or two inch [51 mm] filters.
- EVAPORATOR COIL - Two circuit, interlaced row split coils are constructed with copper tubes and aluminum fins mechanically bonded to the tubes for maximum heat transfer capabilities. All coil assemblies are leak tested up to 450 PSIG [3100 kPa] inter-nal pressure prior to installation into units.
- REFRIGERANT CONNECTIONS - Field piping connections are made through a fixed post between two side access panels on either side of the unit. Allows flexibility to meet most field condi-tions as well as full accessibility after the installation is complete. Units may be used with two straight cool condensing units or single circuit manifolded in the field using the copper fittings shipped with each unit.
- DRAIN PAN - The galvanized steel drain pan is designed to trap condensate in either vertical or horizontal installations. Conden-sate drain connections are located on both sides of the unit allowing complete flexibility to meet most field conditions.
- SERVICE ACCESS - Two removable panels on top and each side of the unit are easily removed for access to motors, blowers, sheaves, and filters.
- HORIZONTAL OR VERTICAL - All models are designed for either application and can be installed in either position as sup-plied from the factory.
- TESTING - All units are run tested at the factory prior to ship-ment. Units are shipped with a holding charge of nitrogen.
- HEAT PUMP - The RHCLP Air Handler is designed for heat pump applications. It has two TX valves with internal check valves that allow reverse flow to occur, providing superior control during heating and cooling cycles. The RHCLP Air Handler has been rated and certified to operate with 7.5 ton remote heat pumps.
| Type | Heat Pump |
| Series | Standard |
| Cooling Capacity | 90 Kbtu/hr |
| Nominal Capacity | 7.5 ton |
| Voltage Rating | 208-240 VAC |
| Number of Stages | 2 |
| Drive | Low Static |
| Brand | RUUD® |
| Item Width | 56 in |
| Item Length | 56 in |
| Item Height | 32 in |
| Manufacturer | Rheem Manufacturing |
| UPC | 662021534904 |
| Manufacturer Part Number | RHCLP2090CAR |
UL Listed
Notice
Price/Availability Accessible On Login- C-20 LICENSE & EPA CERTIFICATE REQUIRED FOR PURCHASE OF THIS PRODUCT
- DISCONTINUED ITEM *ALL SALES FINAL* NO RETURNS
- Recommended Accessories
- Competitive Brands
- Recently Viewed
No applicable products
No applicable products
No applicable products
RUUD®Commercial Heat Pump Air Handler, 7.5 ton, 2-Stage, R410A, 208-240/3, Standard, Belt VFD Low Static
- Customers Also Purchased
No applicable products